Men's Safety Boot Baffin Workhorse EPS −60 °C

Men's Safety Boot Baffin Workhorse...
Baffin Men's Extreme Cold Workhorse Boots
Baffin Men's Extreme Cold Workhorse Boots
Baffin Men's Extreme Cold Workhorse Boots
Baffin Men's Extreme Cold Workhorse Boots
Baffin Men's Extreme Cold Workhorse Boots
Baffin Men's Extreme Cold Workhorse Boots
Baffin Men's Extreme Cold Workhorse Boots
Baffin Men's Extreme Cold Workhorse Boots
Baffin Men's Extreme Cold Workhorse Boots
Baffin Men's Extreme Cold Workhorse Boots
Baffin Men's Extreme Cold Workhorse Boots
Baffin Men's Extreme Cold Workhorse Boots
BAWO
In stock: Ships within 48 hours
€241.58 TTC
Shipping 24/48 H
POINTURES

Tarif dégressif dès 2 pièces 222,25 € · dès 10 198,10 €
 

Satisfied or refunded

 

Secure payment

SUMMARY

Baffin Workhorse EPS safety boot, rated at an indicative −60 °C / −76 °F, Arctic rated. Polyurethane leather and nylon upper at 28.6 cm (11.25 in), oil and acid resistant, easy-pull eyelets. Composite safety toe and penetration-resistant plate, self-cleaning lug outsole. Removable Comfort-Fit liner that lifts out to dry. CE certified.

TECHNICAL DESCRIPTION

Men's Safety Boot Baffin Workhorse EPS – Extreme Cold

Protection Extreme Cold
Shaft height 28.6 cm (11.25 in)
Safety Composite toe and plate
Protection temperature down to −60 °C / −76 °F*
Sizes EUR 40 to 47
Removable liner Comfort-Fit multi-layer

The extreme cold safety boot with a removable liner

Protection given down to −60 °C / −76 °F*. The Workhorse EPS brings the build of Baffin's polar boots to PPE: a mid-height polyurethane leather and nylon upper resistant to oil and acid, rust-resistant easy-pull eyelets, a rear pull loop. It carries a composite safety toe and penetration-resistant plate, a polyurethane base and a rubber outsole with self-cleaning multi-directional lugs. Inside, a removable seven-layer Comfort-Fit liner that lifts out each evening. Arctic rated, CE certified. EUR sizes 40 to 47.

The Grand-Froid expert view

A safety boot goes on for eight to ten hours a day, five days a week, and that rhythm is what finishes it off: the foot sweats, damp settles into the insulation, and within a month the boot no longer holds the temperature it did on day one. Here the liner lifts out completely — it dries overnight, it sets off dry the next morning, and it can be replaced once it has packed down without touching the shell and its toe cap. Second point that shows up in use: the multi-directional lugs are self-cleaning, releasing mud and packed snow rather than holding onto them, which keeps the grip through the back-and-forth between site and vehicle.

What is it for?

Built for prolonged work in sub-zero cold, at moderate to high activity.

  • Construction and civil works: safety toe and penetration-resistant plate for crushing and puncture risks
  • Petrochemicals and chemical industry: upper, base and outsole resistant to oil and acid
  • Manufacturing and industrial maintenance: all-day wear, moving between workshop and outdoors
  • Food processing and cold stores: controlled temperatures, wet floors, shifts of several hours
  • Farming and livestock: open barns, mud, slurry, full days outside
  • Utilities and network operations: outdoor callouts in all weather

Thermal protection

The Comfort-Fit liner stacks seven layers with distinct jobs. Against the foot, Thermaplush™ draws perspiration outwards before it condenses; the thermoformable B-Tek™ Foam moulds to the shape of the foot; the four-channel hollow fibre B-Tek™ Heat builds the volume of air, which is the real insulator. Midway through the stack, a vaporised aluminium membrane reflects the energy the foot gives off back towards it, DiamondNet™ closes off the passage of air and Hydromax™ clears residual moisture. Under the foot, the polyurethane base cuts conduction with frozen ground or the concrete floor of a cold store, the main route of heat loss when standing still. The Arctic rating places comfort at moderate to high activity. One point decides the outcome: the sock must never grip, because any compression crushes the air and removes the insulation.

Safety and compliance
  • CE certified
  • Safety basic requirements — hybrid toe
  • Penetration resistance by non-metal insert
  • Slip resistance
  • Outsole resistance to fuel oil
  • Composite toe and plate, with no metal parts
  • Coefficient of friction tested to Z195-14 on quarry tile and stainless steel, wet and dry surfaces, at room temperature and in cold conditions
Size guide

Take your usual size. For a half size, go up to the size above. The liner moulds to the foot after a few hours of wear. Wear a thick sock with no tightness.

EUR US UK cm
40 7 6 25
41 8 7 26
42 9 8 27
43 10 9 28
44 11 10 29
45 12 11 30
46 13 12 31
47 14 13 32

Baffin industrial grid, distinct from the brand's outdoor grid. Half sizes are not offered on this model: those requirements move up to the size immediately above.

Technical features
  • Mid-height polyurethane leather and nylon upper, 28.6 cm (11.25 in) high in EUR 42, resistant to oil and acid
  • Rust-resistant easy-pull eyelets for a firm fit
  • Rear pull loop for easier entry
  • Composite safety toe and penetration-resistant plate
  • Polyurethane base and rubber outsole, resistant to oil and acid
  • Self-cleaning multi-directional lug outsole
  • Removable multi-layer Comfort-Fit liner, lifts out to dry
  • B-Tek™ Dry waterproofing at the base
  • Weight 3.51 kg (7.74 lb) per pair in EUR 42, forefoot width 12.7 cm (5 in), outer length 33.0 cm (13 in)
  • Sizes EUR 40 to 47, black
Composition
  • Upper: premium polyurethane leather and nylon, laces and stitching
  • Base: polyurethane, rubber outsole, B-Tek™ Dry waterproofing
  • Safety: composite toe and plate
  • Liner — inner layer: Thermaplush™, moisture wicking
  • Liner — structure: thermoformable B-Tek™ Foam and four-channel hollow fibre B-Tek™ Heat
  • Liner — reflection: vaporised aluminium membrane
  • Liner — lining: PolyWool™ wool and polyester blend
  • Liner — air and water management: DiamondNet™ windproofing, Hydromax™
Care & Durability
  • Leather upper: apply a colourless shoe cream to the surface
  • Polyurethane base: wipe with a damp cloth, then dry in open air
  • Take the liner out every evening and let it dry in open air: that is the habit that preserves the insulating power across a season
  • Dry away from any direct heat source
  • Rinse after exposure to chemicals or slurry
  • Check the toe cap, the outsole and the upper-to-base join regularly: damaged PPE is replaced, not repaired
Return or exchange — 30 days
You have 30 days from delivery to request a return or an exchange on this item.

Why choose the Workhorse EPS?

Because it brings to a safety boot what the category usually lacks: a removable liner. On daily wear, that is what decides the comfort temperature over the months, since it dries every night and can be replaced independently of the shell. Added to that are the composite toe and plate, which hold the mechanical protection without conductive metal, and a self-cleaning outsole that keeps its bite between site and vehicle.

On daily wear, what wears a work boot out is not the cold, it is the damp you leave inside it

* Indicative temperature. Perceived warmth varies with activity, body type, humidity, wind, length of exposure and the socks worn.

You might also like

Satisfied or
refunded
Delivery charge free
from 1000 € *CEE Only
Secure payment
Our customer service
at your service